Thursday, September 5, 2019

Mikael Sundgren 1950-2019

We have lost a big RC boating profile!


Wednesday August 21 we lost my friend Mikael Sundgren after a short illness.

I've known Mikael since the mid 80's when I shifted to hydroplane RC boats from racing off-shore boats before that. After we booth made a comeback to boating some 13-14 years ago, me and Micke have shared many trips to the ponds and races around Europe. He was the one I discussed technical solutions with whenever I had some doubts or that I just wanted his opinion.

He has also been very helpful and influential in the development and testing of all KEP's boats.

I've lost one of my best friends.

R.I.P.


The funeral service will be held at Pilgrimskapellet in Järfälla Wednesday September 18 at 13.30.

More info of the funeral service can be found HERE









Friday, April 26, 2019

Invitation Swedish iMBRA H&O League 2019

Here is the invitation to the Swedish iMBRA Hydro & Offshore League race in Oxelösund end of May.


The race includes:

• iMBRA H&O League
• Nordic Champs 2019
• Swedish Champs Race 2
• NC2 (Norway Cup Race 2)






Monday, October 15, 2018

Höstmöte & R/C Båt Träff 2018!


Höstmöte FSR-O & H samt R/C Båt Träff

  • Datum: Lördagen den 17 November 2018
  • Plats: Minicarshuset Enköping
  • Samling: 09.30
  • Start: 10.00
  • Lunch: Om ni önskar lunch så kostar den 140:- i kontanter eller Swish - Notera att i lunchen ingår även fikat under dagen
  • Anmälan: Obligatorisk (och bindande vad gäller lunchen). Anmäl er senast Söndagen den 11:e November till niklas@minicars.se – var god notera vid anmälan hur många ni kommer och hur många lunch ni önskar.
Dagordning (provisorisk):
  • 09.30-10.00: Ankomst fika/frukost
  • 10.00: Sektionsmöte FSR-O & FSR-H
  • 13.00: Lunch
  • 14.00: Fortsättning av mötet och efterföljande R/C Båt snack tills vi tröttnar...
Välkomna!

Mvh,

O&H sektionen - Mattias & Lelle

Sunday, August 5, 2018

KEP's 21 World Champion 2018!

iMBRA 2018 Hydro World Championships Egletons France

Hydro 3.5 Results:
1. Martin Fields - UK - 1169p - KEP's 21
2. Keith Burgess - UK - 927p - KEP's 21
3. Dominique Marzolf - France - 863p - Rocket
4. Mattias Bengtsson - Sweden - 575p - KEP's 21
5. Benoit Argoud - France - 519p - KEP's 21
6. Christian Hoff - Germany - 475p - Warlok (edited)
7. Winfried Ott - Germany - 450p - JAE
8. Markus Schwab - Germany - 25p - ?








Monday, May 7, 2018

SAW Nitro Record 134MPH = 215 KPH

SAW Nitro World Record 134MPH = 215 KPH!

Earlier this April Martin Truex Jr set a new straightaway world speed record in a SAW event in Huntsville with an impressive 215 KPH!


  • Average 2-way speed: 134 MPH (215 KPH)
  • Fast past: 135.054 MPH (217 KPH)
  • Motor: CMB VAC .91
  • Prop: ABC 2727 - 19° rake - 38% blade area
  • Radio: Futaba




Friday, March 16, 2018

KEP's T3-45 V2 Freebie




Presenting the updated KEP's T3-45 V2 Freebie!


Main KEP’s T3-45 V2 News (compared to the earlier KEP’s T3-45):

  • New Turn-Fin Mount!
  • New Turn-Fin!
  • New Sponsons to accommodate the new turn-fin mount!



Other Features:

  • New Turn-Fin. The new shape makes it more planted on the water and its easier to turn left.
  • New Turn-Fin Mount: The new plate mount is more rigid and is easier to make. It can be made in high strength carbon or hard aluminium.
  • Kick Up. The rear part of the tub bottom has a kick-up of 2 mm (The original T3-45 had that also).
  • Longer sponson ride-pads. Improves rough water handling.
  • Slightly new nose section of the tub. Even more rounded nose block plus a little stretched-out side profile in the nose.
  • 3 mm longer C-C spacing of the sponson tubes. That is to accommodate a slightly bigger tank.
  • Top deck leaning forward. The tub deck where the cowl sits is leaning forward (as it also did on the earlier version).
  • Optional ski designs. The ski’s are the same as the earlier T3-45. The optional ski with strakes on the flat running surface improves the tracking and side stability but it’s bit more difficult to do.
  • Longer fuel cell. The earlier T3-45 tank still fits but now you can make it 3 mm longer for more fuel capacity. It’s more common now to make the tanks in plastic and that takes away volume as they use thicker material.


Specifications:
  • After plane length: 650 mm (26.6")
  • Overall length from transom to the tip of the sponsons: 900 mm (35.45")
  • Outside-Outside sponson spacing: 560 mm (22")
  • Tub length: 796.5 mm (31.36")
  • Tub inside width: 76 mm (2.99")
  • Tub outside width (with 6 mm thick sides): 88 mm (3.46")
  • Tub height: 55 mm (2.16")
  • Sponson width: 34 mm (1.39")
  • Sponson ride pads (removable): 2 x 40 x 200 mm (.079" x 1.57" x 7.87")
  • Ride pads AoA: 3.6°
  • Ski width: 40 mm (1.57")
  • Ski AoA: 1.5°
  • Belly height: 24.8 mm (.98”) (from belly to the drink)

Recommendations:
  • Futaba 4PV radio
  • 2x Futaba S3172SV mini servos for channel 2 & 3
  • Futaba BLS571SV low profile steering servo
  • Vapex 1600 mAh 2S LiFe receiver battery
  • 8 x 10 mm pultruded carbon sponson tubes (550 mm long)
  • 10 x 12 mm aluminum tubes for the tub and sponsons
  • 2x12 mm steel pin for securing the sponson tubes (much better then any other securing system we've tried by far).

Fuel Cell Manufacturers:
  • Ian’s Boats - Welded Plastic tanks with brass nipples - www.iansboats.co.uk
  • Walter Barney - Stainless tanks with brass tubes - wjbarney@tds.net
  • John Steltzer - Stainless tanks & stainless tubes - johnstelzer@yahoo.com

Note, this is the last giveaway freebie rigger design I have planned to do. So: Build it. Race it. Enjoy! :)



KEP's T3-45 V2 Main Drawing - The Freebie drawings paper size: 980 x 594 mm. Make sure that it's printed 1:1 scale / 100% size. Click HERE for download (works best on a stationary normal PC/Mac).


KEP's T3-45 V2 Templates Drawing - The Freebie drawings paper size: A1 = 841 x 594 mm. Make sure that it's printed 1:1 scale / 100% size. Click HERE for download (works best on a stationary normal PC/Mac).


If you have the earlier KEP's T3-45 "V1" - Click HERE for a download of an updated "V2" fin that is adapted for the T3-45 "V1" turn-fin mount. This turn-fin does not fit the T3-45 V2 boat as it has a different turn-fin mount!




This is a size comparison with the KEP's T3-45 V2 (top) and the T3-21 V2 (on the bottom).